How To Clean White Cement Leftover?
Removing dry white cement residues from any surface can be a very complicated task to perform, a very important tip for this is to use a green pad scrubber, one of those used to clean dishes in the kitchen.
This pad has an ideal texture to remove the white cement without having to scratch or mistreat the surface where it is stuck, for this you must soak the green pad in water and squeeze several times the area where the white cement is stuck.
Then, you can remove the dust with a wet cloth or simply wipe the floor with a mop.
How to Remove Dried White Cement From Tiles?
To remove dried white cement from tiles, there are several steps to follow that will ensure you do it right. The reason why you have different approaches is because of the size and type of cement stain.
For example, if you’re dealing with light stains that are almost translucent, then a good scrubbing will get the job done. However, if you’re dealing with big chunks of cement, it’s best to use a scraper.
To get started, you’ll need the following:
- Towels
- Scraper
- Masks
- Hard scrub brush
- Dish soap
- Vinegar
- Cement remover
Once you gather the items above, start by cleaning the floor to remove white cement from the tile. This will ensure no major grime, dirt, or dust is close to the area you’re planning to work. Then apply vinegar or cement remover to clean the white cement stains. Block off the area to prevent pets, kids, and other people from walking through and disrupting the process.
Next, scrape and scrub the large stains then give the area a good cleaning with soap and water. Finally, seal the area as this ensures the surface resists stains and leaves the area looking better.
How to Remove White Cement From the Floor?
If white cement stained your marble floor, you can remove the stains by using white vinegar. Simply take a clean soft cloth and soak it in diluted white vinegar. Place the cloth over the white cement stains on the marble floor and leave it for a minimum of 1 hour.
This will allow the vinegar to break down the cement. If the soft cloth starts to dry out, soak it again in vinegar and place it over the stain(s). After another hour, use a scrubbing pad to scrub the white cement stains away.
If the scrubbing pad does not work, use a scraper. Repeat the steps above until all the white stains are fully removed.
However, you should be very careful with calcareous stones, such as marble. The acid could damage the marble. In addition, vinegar can also damage, for example, silicone edges in the bathroom.
How to Remove White Cement From Steel?
Steel is a common material in construction sites. After work, construction workers usually notice cement stains on the steel plates, steel bars, and steel rods. Leaving the stains as they are limits the life of the steel plates, steel bars, and steel rods.
In fact, it reduces their working capacity. To maintain their strength, you need to clean these bars, plates, and rods.
Here is how:
Make sure the stained area is not oily, and try to make cracks between the dried white cement. This will allow the cement remover chemical to go between the cracks and work faster.
Now, apply the cement or concrete remover chemical onto the dried white cement. Allow the chemical to work. This takes at least 20 to 30 minutes. Using a soft cloth, gently wipe off the paste then rinse the remaining dirt with water.
You can use a low-impact power washer or a hose nozzle. Allow the steel to dry. By following the steps above, you can protect your steel plates and rods from degrading.
How to Remove Hardened White Cement From Glass?
Removing hardened white cement from glass is a challenge. However, we researched and found the best method of removing hardened white cement from glass.
Fill your spray bottle with 3 drops of dishwashing soap and water. Shake the bottle well and spray down the window. This will lubricate the glass to prevent scratching and saturate the white cement making it easier to remove.
After a couple of minutes, use a plastic knife to scrape the white cement from the glass. Then rinse the glass with your hose and sponge away any remaining white cement particles.
Alternatively, apply the cement remover to the glass and make sure to follow the manufacturer’s directions. Leave it to soak and after a couple of minutes, use a putty scraper to scrape away the cement. Rinse the glass then dry it off.
Overview of Homemade Alternatives for Removing Hardened White Cement From Surfaces
The following are homemade alternatives for removing hardened white cement.
- Diluted white vinegar or Pure vinegar
- Dishwashing soap
- Water
- heavy-duty green pad scrubber
A mixture of dishwashing soap and water in a spray bottle or soaking a soft cloth in diluted white vinegar helps soften the white cement stains. This makes it easy for you to remove them using a scrapper. In fact, it helps remove stains without leaving any scratches on the surface.
Suggested Chemical Product for Removing White Cement
Some basic chemicals can be effective in removing white cement, for example:
Goo Gone, this softener and remover can be used to remove white cement residue on tiles and stainless steel, it is not recommended on porous surfaces, so to be used on concrete, this must be previously sealed.
Also, there is this non-acidic and biodegradable product that is mixed with hot water to remove concrete, cement or grout.
